CentOS Stream 8
Sponsored Link

Initial Settings : Network Settings2021/02/19

 
If you did not configure network settings during the CentOS Stream Installation, Configure it like follows.
[1] To set static IP address to the server, Modify settings like follows.
( Replace the interface name [enp1s0] to your own one because it's not the same on any System )
# if you did not set HostName, set it like follows

[root@localhost ~]#
hostnamectl set-hostname dlp.srv.world
# display devices

[root@localhost ~]#
nmcli device

DEVICE  TYPE      STATE      CONNECTION
enp1s0  ethernet  connected  enp1s0
lo      loopback  unmanaged  --

# set IPv4 address

[root@localhost ~]#
nmcli connection modify enp1s0 ipv4.addresses 10.0.0.30/24

# set gateway

[root@localhost ~]#
nmcli connection modify enp1s0 ipv4.gateway 10.0.0.1

# set DNS

# for multiple DNS, specify with space separated ⇒ ipv4.dns "10.0.0.10 10.0.0.11 10.0.0.12"

[root@localhost ~]#
nmcli connection modify enp1s0 ipv4.dns 10.0.0.10

# set DNS search base (your domain name)

[root@localhost ~]#
nmcli connection modify enp1s0 ipv4.dns-search srv.world

# set [manual] for static setting (it's [auto] for DHCP)

[root@localhost ~]#
nmcli connection modify enp1s0 ipv4.method manual

# restart the interface to reload settings

[root@localhost ~]#
nmcli connection down enp1s0; nmcli connection up enp1s0

Connection 'enp1s0' successfully deactivated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/1)
Connection successfully activated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/2)

# confirm settings

[root@localhost ~]#
nmcli device show enp1s0

GENERAL.DEVICE:                         enp1s0
GENERAL.TYPE:                           ethernet
GENERAL.HWADDR:                         52:54:00:A1:D5:6E
GENERAL.MTU:                            1500
GENERAL.STATE:                          100 (connected)
GENERAL.CONNECTION:                     enp1s0
GENERAL.CON-PATH:                       /org/freedesktop/NetworkManager/ActiveC>
WIRED-PROPERTIES.CARRIER:               on
IP4.ADDRESS[1]:                         10.0.0.30/24
IP4.GATEWAY:                            10.0.0.1
IP4.ROUTE[1]:                           dst = 10.0.0.0/24, nh = 0.0.0.0, mt = 1>
IP4.ROUTE[2]:                           dst = 0.0.0.0/0, nh = 10.0.0.1, mt = 100
IP4.DNS[1]:                             10.0.0.10
IP6.ADDRESS[1]:                         fe80::f724:5898:361d:da04/64
IP6.GATEWAY:                            --
IP6.ROUTE[1]:                           dst = fe80::/64, nh = ::, mt = 100
IP6.ROUTE[2]:                           dst = ff00::/8, nh = ::, mt = 256, tabl>

# confirm state

[root@localhost ~]#
ip address show

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether 52:54:00:a1:d5:6e brd ff:ff:ff:ff:ff:ff
    inet 10.0.0.30/24 brd 10.0.0.255 scope global noprefixroute enp1s0
       valid_lft forever preferred_lft forever
    inet6 fe80::f724:5898:361d:da04/64 scope link noprefixroute
       valid_lft forever preferred_lft forever
[2] If you don't need IPv6, it's possible to disable it like follows.
# disable IPv6

[root@localhost ~]#
grubby --update-kernel ALL --args ipv6.disable=1

# verify kernel parameters

[root@localhost ~]#
grubby --info DEFAULT

index=0 kernel="/boot/vmlinuz-4.18.0-348.2.1.el8_5.x86_64" args="ro crashkernel=auto resume=/dev/mapper/cs-swap rd.lvm.lv=cs/root rd.lvm.lv=cs/swap console=ttyS0,115200n8 selinux=0 ipv6.disable=1 $tuned_params" root="/dev/mapper/cs-root" initrd="/boot/initramfs-4.18.0-348.2.1.el8_5.x86_64.img $tuned_initrd" title="CentOS Linux (4.18.0-348.2.1.el8_5.x86_64) 8" id="54f4bd7df8464337a3009215fdef55fb-4.18.0-348.2.1.el8_5.x86_64"
[root@localhost ~]#
[root@localhost ~]#
ip address show

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
2: enp1s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether 52:54:00:a1:d5:6e brd ff:ff:ff:ff:ff:ff
    inet 10.0.0.30/24 brd 10.0.0.255 scope global noprefixroute enp1s0
       valid_lft forever preferred_lft forever

# if falling back to enable, run like follows

[root@localhost ~]#
grubby --update-kernel ALL --remove-args ipv6.disable

Matched Content